Cen-tech Digital Multimeter 69096 Manual

An electrically savvy handyman frequently carries a digital multimeter in his tool box or service vehicle. A properly used multimeter measures both voltage and current for alternating current, or AC. The multimeter also measures voltage and current for direct current, or DC. Electronic hobbyists can also test diodes, resistors and transistors with the Cen-Tech 92020 digital multimeter. Safety-conscious workmen and hobbyists receive prior instruction in the multimeter’s operation, as the device measures potentially deadly electrical voltages.

Measuring AC Voltage

Place the red lead’s plug end into the jack marked “V-ohm-mA.” Place the black lead’s plug end into the jack marked “COM.”

Set the multimeter to read AC voltage. Turn the range selector knob to the position marked “750 ACV.”

Turn the meter on. Slide the power switch to the “On” position.

Touch each probe to the item for which voltage is being measured. Use the probe ends of the leads. Do not allow your fingers to touch the probes, as lethal voltage may be present.

Digital Multimeter Troubleshooting and Repair April 22, 2014 June 20, 2014 George 0 Comments digital multimeter repair, digital multimeter troubleshooting, dmm help, repairing dmm Your digital multimeter should last for a number of years with reasonable care, but there may come a time when you multimeter malfunctions and you’ll have to. Cen-Tech provides a a range of digital multimeter solutions for consumers and contractors working in the electrical industry. According to Kenneth Wills, an electrician with CONSOL Energy, the standard Cen-Tech multimeter will measure both alternating and direct current voltage, in addition to measuring resistance and amps.

Read the digital display’s indicated voltage. Adjust the range selector knob to a lower range if the voltage is less than 200 volts.

Turn the meter off. Slide the power switch to the “Off” position.

Cen Tech Multimeter 69096 Instructions

Measuring DC Voltage

Place the red lead’s plug end into the jack marked “V-ohm-mA.” Place the black lead’s plug end into the jack marked “COM.”

Set the multimeter to read DC voltage. Turn the range selector knob to the position marked “1,000 VDC.”

Turn the meter on. Slide the power switch to the “On” position.

Touch each probe to the item for which voltage is being measured. Use the probe ends of the leads. Do not allow your fingers to touch the probes, as lethal voltage may be present.

Read the digital display’s indicated voltage. Adjust the range selector knob to a lower range if the voltage is less than 200 volts.

Turn the meter off. Slide the power switch to the “Off” position.

Measuring DC Current

Place the red lead’s plug end into the jack marked “10A.” Place the black lead’s plug end into the jack marked “COM.”

Set the multimeter to read DC current. Turn the range selector knob to the “10A” position.

Cen

Turn the meter on. Slide the power switch to the “On” position.

Touch each probe to the item for which current is being measured. Use the probe ends of the leads.

Cen-tech Digital Multimeter 69096

Read the digital display’s indicated current. Adjust the range selector knob to the “200 mA setting.” Move the red plug to the “VmA” jack if the reading is 200 mAmps or less.

Cen-tech Digital Multimeter 69096 Manual

Turn the meter off. Slide the power switch to the “Off” position.

Measuring Resistance

Turn off the power to the device for which resistance is being measured. This ensures the multimeter will not be damaged.

Place the red lead’s plug end into the jack marked “V-ohm-mA.” Place the black lead’s plug end into the jack marked “COM.”

Set the multimeter to read resistance. Turn the range selector knob to the “200 ohm' position.

Turn the meter on. Slide the power switch to the “On” position.

Touch the red and black probes together. The display should indicate a resistance of 0 ohms.

Touch each probe to the item for which resistance is being measured. Use the probe ends of the leads.

Read the digital display’s indicated resistance. Adjust the range selector knob to the next higher setting if the meter reads “1.”

Turn the meter off. Slide the power switch to the “Off” position.

Measuring Transistor hFE or Gain

Set the multimeter to read transistor hFE. Turn the range selector knob to the “hFE” position.

Turn the meter on. Slide the power switch to the “On” position.

Insert the transistor pins into the appropriate transistor jack; either “NPN” or “PNP.” Place the transistor’s emitter pin in the “E” jack. Place the collector in the “C” jack. Place the base in the “B” jack. Obtain the type of transistor and pin out from online reference material.

Read the transistor’s hFE indicated on the digital display.

Turn the meter off. Slide the power switch to the “Off” position.

Kitserver pes 2011 install download. CATEGORY: Pes 2011 Kitservers. PES 2011 Kitserver 11.1.1 by juce. Jun - 18 - 2011. Tags: kitserver 11.1.1 download,pes 2011 kitserver download. PES 2011 Face Server Beta 6 for Kit Server 11 by Juce New Features: – added support for BAL mode. Here you can download kitserver 2011 shared files: Kitserver 2011.part1.rar from mediafire.com 87 MB, Kitserver 2011 v10 0 2 by juce robbie para pes 2011 pc from uploading.com (11 MB), Print page kitserver 2011 v10 1 0 sadrži dugo očekivani lod mixer from uploading.com (10 MB), Kitserver 2011 v11 1 0 new version released 10 06 by juce robbie from mediafire.com (12 MB), Mf kitserver 2011 v10. Feb 22, 2011  DOWNLOAD KIT SERVER 11 for PES 2011 PES 2011 Kit Server 11 Kitserver 2011 is an add-on program for. Oct 03, 2011  Question: I download the kitserver and place it in the pes 2011 map in C. But when I click on the manager.exe, select pes 2011.exe (only one there) I get an error: 'setup failed to install kitserver 2011 for. Mar 24, 2011  Download PES 2011 Kit Server 11.0.3.2 + LOD Mixer Update. Kitserver v11.0.3.2. Supports: PES 2011 demo, 1.0, 1.01, 1.02 and 1.03 game versions. The following modules are included: – afs2fs: manage your BINs in folders – simple and easy, multiple roots supported – speeder: adjust the game speed to your liking.

Measuring Diode Voltage Drop.

Place the red lead’s plug end into the jack marked “V-ohm-mA.” Place the black lead’s plug end into the jack marked “COM.”

Cen-tech digital multimeter 69096 manual pdf

Set the multimeter to read diode voltage drop. Turn the range selector knob to the diode position.

Turn the meter on. Slide the power switch to the “On” position.

Touch the black probe to the diode’s cathode. Touch the red lead to the diode’s anode. Use the probe ends of the leads. The cathode has a dot or ring marking on the diode.

Read the diode voltage drop indicated on the digital display.

Turn the meter off. Slide the power switch to the “Off” position.